I should point out that I am not affiliated with either company, I signed up for a Zenfolio trial and thought I would compare the results of both before recommending them to clients. This is not a detailed scientific comparison of prints, its 5 minutes with a scanner.

It is difficult to compare physical prints online, but before I gave the prints out I quickly scanned them using a Canon MP560 scanner/printer, zipped them through Adobe Lightroom to match the crops as closely as possible and exported them below. Apologies for the poor crop, I scanned them so quickly I used the same automatic settings on each and for some reason the software took an inch off either side.

The left most picture is the original from Adobe Lightroom which was colour matched using a Colour Checker Passport, the middle picture is from One Vision Imaging, and the right most picture is from PhotoBox.

Remember the same automatic settings were used on each of the two scans, apart from differences in brightness the scanned images do reflect the physical prints well and do demonstrate difference between the physical prints.

As you can see, the colour of the child’s truck in the PhotoBox image does not match that of the original, and the skin tone is also off on the PhotoBox photograph. The One Vision Imaging photograph is far closer in terms of the trucks colour and the skin tone.

Physically the One Vision Imaging print is as accurate as you can imagine a print to be in terms of the truck, skin tone and colour of the child’s T-Shirt. The PhotoBox is not without merit though as it does have a vibrance about it, but for me the vibrance should not mean sacrificing the colour accuracy to this degree.

I still intend on offering both on Zenfolio, PhotoBox provides a surprising variety of products and are cheaper than One Vision Imaging, but it does prove that you get what you pay for so I will be recommending One Vision Imaging for those must have prints.

1. When installing Ubuntu Server include BIND for DNS, if you have already installed Ubuntu without BIND use sudo apt-get install bind9 dnsutils to install;
2. Configure your two network cards with different IP addresses, one for the LAN and one for the WAN side;
3. Configure BIND to act as a forwarder only using BIND9ServerHowto;
4. Install and configure Squid and ClamAV as explained here, I personally used the comment from Jayson D. Martinez How to Setup Transparent Squid Proxy Server in Ubuntu, but I did not install the web admin tools;
5. Also install the ClamAV Daemon using sudo apt-get install clamav-daemon
6. When configuring squid, check the default file thoroughly, consider making a backup and recreate the file from scratch;
7. The iptables configuration from here works better Squid transparent proxy with iptables
8. Configure a machine behind the second network card, using the Ubuntu server as a gateway and test.

If you have any problems check:-

- The squid log files in /var/log/squid/;
- The port number you configured in squid.conf is the same one you used in the iptables line and that you have added transparent to the http_port line of the squid.conf file;
- Manually configure a browser to use the ubuntu server as a proxy to rule out a problem with the iptables.

You could also extend this configuration using a web content filter like DansGuardian Squid Proxy Server On Ubuntu 9.04 Server With DansGuardian, ClamAV, And WPAD the link also contains useful notes on checking the ClamAV installation is updating correctly.

1. Download the ISO and mount in Finder
2. Copy the file imagedd.bz2 from the mounted ISO to a location on your hard disk
3. Insert the target USB key in to your Apple Mac
4. Open a terminal window
5. Run diskutil list, locate the USB key in the list for this example we will say it is /dev/disk5
6. Run diskutil unmountDisk /dev/disk5 it will disappear from Finder but will still be accessible from the command line
7. Run bzcat imagedd.bz2 | dd of=/dev/disk5, you will need to specify the location of the .bz2 file you copied in step 2
8. Wait for the process to finish, it may take some time
9. When the prompt reappears check bytes were successfully transferred, if not check your previous commands
10. Run diskutil eject /dev/disk5 to eject the disk, it can now be removed from the Mac
11. Insert the USB key in to the server/pc you are going to run ESXi and power it up.

It is important to note this will boot in to ESXi directly and is not the installer. Once started your can set the root password and configure using the menu system.

The same process could be used for installation on to SD Cards, but check the hardware compatibility lists on vmware.com.

I usually do this by rating images in Apple Aperture, first going through and giving anything worth a second look two stars, these I review and tidy up before rating them with three stars or higher if the image is ‘exceptional’.

At this point I like input from my wife, but sitting a Windows 7 user down in front of a Mac where the mouse is funny and maximise does not maximise things is more hassle than its worth. So I searched the iPad app store and found one of those perfect IPad apps – Pixelsync.

In short its a small app on your iPad and a helper application on your Mac which allows for projects in your Aperture library or iPhoto to be viewed, rated and flagged on your iPad. There does appear to be a restriction that like iTunes and the iPad or iPhone sync the library must be open in Aperture although Aperture does not need to be running at the time. It would be nice if this restriction could be resolved in both iTunes and Pixelsync but that is probably an Aperture restriction so outside of the control of the author of Pixelsync.

With the helper application on your Mac configured to open your library from the iPad you can select which projects within that Library will be synchronised to your iPad. Once synchronised you can rate and flag your images before synchronising back to Aperture.

The application works perfectly and my wife enjoyed rating the images while sitting on the sofa drinking a cup of tea far more than sitting in front of my Mac using a funny mouse.

I believe Pixelsync has been available for a while, and I meant to write this a while back. The appearance of Photosmith for the iPad which appears to be a similar app but for Adobe Lightroom reminded me to put finger to key and post this.

Pixelsync can be purchased on the app store and more information along with the helper application can be downloaded from http://www.pixelsyncapp.com/.

The VMWARE vSphere client closes or crashes when you right click on a host and select Import Machine.

Cause

You probably have an older version of the VMWARE client such as VI Client 2.5 installed for administration of older ESX installations.

There is a DLL conflict documented in http://www.vmware.com/support/vsphere4/doc/vsp_vcc_41_rel_notes.html, although it describes a Visual C++ Runtime error which I did not receive.

Resolution

The solution documented in the release notes works though which is to remove (although I suggest rename) the following files located in C:\Program Files\VMware\Infrastructure\Virtual Infrastructure Client\Launcher:-

• libeay32.dll
• ssleay32.dll

Once renamed/removed if you have the vSphere client open, close the client and open it again otherwise simply open the vSphere client. The vConverter utility should now run when you use Import Machine.

MPDB ERROR – CONNECTION PARAMETERS
SQL Server Name : database_servername
SQL Database Name : sms_sitename
Integrated Auth : True

MPDB ERROR – EXTENDED INFORMATION
MPDB Method : Init()
MPDB Method HRESULT : 0×80004005
Error Description : Cannot open database “sms_sitename” requested by the login. The login failed.
OLEDB IID : {0C733A8B-2A1C-11CE-ADE5-00AA0044773D}
ProgID : Microsoft OLE DB Provider for SQL Server

MPDB ERROR – INFORMATION FROM DRIVER
SQL Server Name : database_servername
Native Error no. : 4060
Error State : 1
Class (Severity) : 11
Line number in SP : 1

In addition your database server may well be logging event id 6512

Event Type: Error
Event Source: MSSQLSERVER
Event Category: (2)
Event ID: 6512
Date: 24/11/2010
Time: 18:18:53
User: domain\serviceaccount
Computer: database_servername
Description:
Failed to initialize the Common Language Runtime (CLR) v2.0.50727 with HRESULT 0×80004005. You need to restart SQL server to use CLR integration features.

When you check the whether CLR is enabled using the SQL Server Surface Area Configuration you may find it is, and that it has been enabled in the past because advertisments and deployments worked in the past.
It is the solution though, no matter how much you don’t like it, a critical update or service pack may have been applied to the .net framework 2.0 since it last worked and SQL Server requires a restart. If you want to be sure you can browse the database assemblies under programability and you will probably receive the same error message.
Time to suck it up, stay late and do a 30 second restart of the SQL server and agent services. Following that restart the SMS Executive and related services on your Configuration Manager server and within minutes your world will be a better place.